BS EN 10111-2008 Continuously hot-rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions
|
ID： |
02DA9FD2E3B84D2E9F0FD188497DFA78 |
|
文件大小(MB)： |
0.33 |
|
页数： |
16 |
|
文件格式： |
|
|
日期： |
2008-10-9 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
BRITISH STANDARD BS EN,10111:2008,Continuously hot rolled,low carbon steel sheet,and strip for cold,forming — Technical,delivery conditions,ICS 77.140.50, , , ,Copyright British Standards Institution,Provided by IHS under license with BSI - Uncontrolled Copy,No reproduction or networking permitted without license from IHS Not for Resale,--`,,```,,,,````-`-`,,`,,`,`,,`---,BS EN 10111:2008,This British Standard was,published under the authority,of the Standards Policy and,Strategy Committee,on 30 May 2008,. BSI 2008,ISBN 978 0 580 54793 5,National foreword,This British Standard is the UK implementation of EN 10111:2008. It,supersedes BS EN 10111:1998 which is withdrawn.,The UK participation in its preparation was entrusted to Technical Committee,ISE/10, Flat rolled steels products.,A list of organizations represented on this committee can be obtained on,request to its secretary.,This publication does not purport to include all the necessary provisions of a,contract. Users are responsible for its correct application.,Compliance with a British Standard cannot confer immunity from,legal obligations.,Amendments/corrigenda issued since publication,Date Comments,Copyright British Standards Institution,Provided by IHS under license with BSI - Uncontrolled Copy,No reproduction or networking permitted without license from IHS Not for Resale,--`,,```,,,,````-`-`,,`,,`,`,,`---,EUROPEAN STANDARD,NORME EUROPéENNE,EUROP腎SCHE NORM,EN 10111,April 2008,ICS 77.140.50 Supersedes EN 10111:1998,English Version,Continuously hot rolled low carbon steel sheet and strip for cold,forming - Technical delivery conditions,T鬺es et bandes en acier doux laminées à chaud en continu,pour formage à froid - Conditions techniques de livraison,Kontinuierlich warmgewalztes Band und Blech aus weichen,St鋒len zum Kaltumformen - Technische Lieferbindungen,This European Standard was approved by CEN on 29 February 2008.,CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European,Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national,standards may be obtained on application to the CEN Management Centre or to any CEN member.,This European Standard exists in three official versions (English, French, German). A version in any other language made by translation,under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the,official versions.,CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.,EUROPEAN COMMITTEE FOR STANDARDIZATION,COMITé EUROPéEN DE NORMALISATION,EUROP腎SCHES KOMITEE FüR NORMUNG,Management Centre: rue de Stassart, 36 B-1050 Brussels,. 2008 CEN All rights of exploitation in any form and by any means reserved,worldwide for CEN national Members.,Ref. No. EN 10111:2008: E,Copyright British Standards Institution,Provided by IHS under license with BSI - Uncontrolled Copy,No reproduction or networking permitted without license from IHS Not for Resale,--`,,```,,,,````-`-`,,`,,`,`,,`---,EN 10111:2008 (E),2,Contents Page,Foreword.3,1 Scope ..4,2 Normative references .4,3 Terms and definitions 4,4 Classification and designation.5,4.1 Classification..5,4.2 Designation .5,5 Requirements .5,5.1 Steelmaking and manufacturing processes 5,5.2 Deoxidation .5,5.3 Chemical composition ..5,5.4 Delivery conditions.5,5.5 Mechanical properties..6,5.6 Surface characteristics .6,5.7 Suitability for surface coating ..6,5.8 Weldability7,5.9 Tolerances on dimensions and shape 7,6 Tests.9,6.1 General9,6.2 Inspection units 9,6.3 Number of tests.9,6.4 Sampling9,6.5 Test methods10,6.6 Retests .10,6.7 Inspection document..10,7 Marking 10,8 Packing 11,9 Storage and transportation..11,10 Disputes..11,11 Information to be provided by the purchaser at the time of enquiry and order.11,11.1 Mandatory information..11,11.2 Options 11,Bibliography ..12,BS EN 10111:2008,Copyright British Standards Institution,Provided by IHS under license with BSI - Uncontrolled Copy,No reproduction or networking permitted without license from IHS Not for Resale,--`,,```,,,,````-`-`,,`,,`,`,,`---,EN 10111:2008 (E),3,Foreword,This document (EN 10111:2008) has been prepared by Technical Committee ECISS/TC 13……
……